Sony Projector VPL-EX175 Manual do Utilizador

DATA PROJECTORVPL-EX100VPL-EX120VPL-EX145VPL-EX175VPL-FX30VPL-FX35VPL-FX500LVPL-F400XVPL-F500XVPL-F700XLPROTOCOL MANUAL1st Edition (Revised 1)

6VPL-FX30VPL-FX500L/F700XLITEM List For Picture<Table 1> <Table 2> RemarksItem Number DataItem Upper byte Lower byte Data BytePICTURE MODE

7VPL-FX30ITEM List For Setup<Table 1> <Table 2> RemarksItem Number DataItem Upper byte Lower byte Data ByteINPUT TERMINAL 00h 01h VIDEO 00

8VPL-FX30ITEM List For Status<Table 1> <Table 2> RemarksItem Number DataItem Upper byte Lower byte Data ByteSTATUS ERROR1 01h 01h NO ERROR

9VPL-FX30VPL-EX100/EX120/EX145/EX175ITEM List For Picture<Table 1> <Table 2> RemarksItem Number DataItem Upper byte Lower byte Data BytePI

10VPL-FX30ITEM List For Setup<Table 1> <Table 2> RemarksItem Number DataItem Upper byte Lower byte Data ByteINPUT TERMINAL 00h 01h VIDEO 0

11VPL-FX30ITEM List For Status<Table 1> <Table 2> RemarksItem Number DataItem Upper byte Lower byte Data ByteSTATUS ERROR1 01h 01h NO ERRO

12VPL-FX302-1-2. Infrared Remote Command CodeVPL-FX30/FX35/F400L/F500X15bit categoryx0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF0xBLACK LEVEL ADJ

13VPL-FX30VPL-FX500L/F700XL15bit categoryx0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF0xBLACK LEVEL ADJ TOGGLEPICTURE ADJ TOGGLE1x VOLLARGEVOLSMALLA

14VPL-FX30VPL-EX100/EX120/EX145/EX17515bit categoryx0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF0xBLACK LEVEL ADJ TOGGLEPICTURE ADJ TOGGLE1x VOLLARG

15VPL-FX302-2. Reply<Table 3>Item Number DataItem Data Upper byte Lower byteACK Complete 00h 00hNAK Undefi ned Command 01h 01hSize Error 04hSelec

VPL-FX30! 警告このマニュアルは，サービス専用です。お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災，人身事故につながることがあります。危険をさけるため，サービストレーニングを受けた技術者のみご使用ください。! WARNINGThis manual is in

16VPL-FX30D4 D5 D6 D7(MSB)(LSB) (EVEN) BITPARITY STOPBITSTART D3D2D1D03. RS-232C3-1. ConnectionCommunication is enabled by the use of a D-Sub 9 Pin cr

17VPL-FX303-3. Communication Procedure3-3-1. Outline of CommunicationAll communication between CONTROLLER (PC, etc.) and DEVICE (PROJECTOR) is perfor

18VPL-FX30START CODEB0B1B2B4B3DATAITEM NUMBERTYPECHECK SUM*1END CODEB5B6B7[A9h]Put the item number. Refer to the item list in the sections 2-1-1 and 2

19VPL-FX303-7. Packet Examples3-7-1. Change “ASPECT” to “ZOOM”START CODE = A9hITEM NUMBER = 0020h (ASPECT)SET/GET = 00h (SET)DATA = 0003h (ZOOM)CHECK

20VPL-FX304. EthernetEthernet corresponding modelVPL-FX30, VPL-FX35, VPL-FX500L, VPL-F400X, VPL-F500X, VPL-F700XL, VPL-EX145, VPL-EX1754-1. Service4-1

21VPL-FX304-1-2. PJ TalkBy using PJ Talk, it is possible to communicate with PROJECTOR over Ethernet network. Both of set and get method are provided.

22VPL-FX30CONTROLLER PROJECTORSDCP SET/GET RequestResponse(OK/NG)The command is executed if it’s valid. Then, the receive command is sent to the CONTR

23VPL-FX30HEADER(4)COMMUNITY(4)PRODUCT NAME(12)SERIAL NO.(4)LOCATION(24)POWERSTATUS(2)VERSION (1)4441h (2)CATEGORY (1)COMMUNITY (4)4-3. Protocols4-3-1

24VPL-FX30HEADER(2) COMMUNITY(4) COMMAND(4)DATA(n)VERSION(1) CATEGORY(1)4-3-2. SDCP1. Packet StructureThe Fig. 4-5 shows SDCP packet format. The numbe

25VPL-FX30REQUEST(1) ITEM NO(2)DATA LENGTH(1)4. COMMAND FieldThere are 2 types of COMMAND fi eld, which are REQUEST and RESPONSE. REQUEST command is se

1 (T)VPL-FX30Table of Contents1. Overview1-1. Introduction ... 11-2. Glossary of

26VPL-FX30RESPONSE(1) ITEM NO(2)DATA LENGTH(1)OK[01h] ITEM NO(2)DATA LENGTH[00h]OK[01h] ITEM NO(2)DATA LENGTH(2)NG[00h] ITEM NO(2)DATA LENGTH(2)(2) RE

27VPL-FX305. DATA FieldThe content to be fi lled in this fi eld depends on the COMMAND fi eld. For SET Request commands, appropriate DATA value accompani

28VPL-FX300x8001 Model nameAlphanumeric 12 charactersIf the number of characters is less than 12, the remaining digits are fi lled with 00h.0x8002 Seri

29VPL-FX307. ERROR CODEERROR CODE has 2 bytes long. The table below shows the error code. Each error category is explained in the subsequent sections.

30VPL-FX30(1) Item ErrorThis error occurs when the Item No. of a request is illegal or its data is illegal. The conditions for occur-rence of the resp

31VPL-FX30(3) Request ErrorThis error occurs when header or command is illegal. The conditions of occurrence of the respective errors are shown below.

32VPL-FX30(5) Comm ErrorCommunication between Ethernet controller and main CPU has been failed.TimeoutTimeout occurred.Check Sum ErrorA check sum erro

33VPL-FX304-3-4. PJLinkThe following model is equipped with the PJLink class1 protocol.For details about this protocol, refer to the PJLink specifi cat

34VPL-FX30Command Data RemarkERST ? The following values are returned:6th digit : Fan error5th digit : Lamp error4th digit : Temperature error3rd di

35VPL-FX30. Commands The following 14 commands are supported : (01) [Power control command] POWR (02) [Power status inquiry] POWR ? (03) [Input s

36VPL-FX30(2) [Power status inquiry] POWR?This command obtains the projector’s power status.The projector responds as follows:Returns the following v

37VPL-FX30(4) [Input switch inquiry] INPT?This command obtains the projector’s input status.The projector responds examples as follows:Returns the fo

38VPL-FX30(7) [Error status inquiry] ERST?This command obtains the projector’s error status.The projector responds as follows:Returns the response fo

39VPL-FX30(9) [Input switch list inquiry] INST?This command obtains the input switch list.The projector responds as follows:When normal : Returns a s

40VPL-FX30(13) [Other information inquiry] INFO?This command obtains other information.The projector responds as follows:When normal : Returns a spac

VPL-FX30The material contained in this manual consists of information that is the property of Sony Corporation.Sony Corporation expressly prohibits th

Sony CorporationVPL-EX100 (CN)VPL-EX100 (SY)VPL-EX120 (CN)VPL-EX120 (SY)VPL-EX145 (CN)VPL-EX145 (SY)VPL-EX175 (CN)VPL-EX175 (SY)VPL-FX30 (SY)VPL-FX35

1VPL-FX301. Overview1-1. IntroductionThe projector is remotely controllable over RS-232C as well as Ethernet. It is useful for setting up the projecto

2VPL-FX30RS-232CSimplified CommandAsynchronousSub CommandAMX Device DiscoverySDAPSDCP Specific CommandSNMP DDDPPJLinkHTTPUDP/IPEthernetTCP/IPSDCP (PJ

3VPL-FX302. Common Commands2-1. Sub CommandsSub Command is the value which is used by Simplifi ed Command. Value is assigned for executing func-tion. F

4VPL-FX30ITEM List For Screen<Table 1> <Table 2> RemarksItem Number DataItem Upper byte Lower byte Data ByteASPECT 00h 20h FULL 0000h Set/

5VPL-FX30ITEM List For Status<Table 1> <Table 2> RemarksItem Number DataItem Upper byte Lower byte Data ByteSTATUS ERROR1 01h 01h NO ERROR