Sony STR-DN840 Manual do Utilizador Página 1

4-454-467-52(1)STR-DN840Multi Channel AV ReceiverOperating Instructions

10GBA Input indicatorLights up to indicate the current input.HDMIThe receiver recognizes the equipment connected via an HDMI IN jack.ARCTV input is se

100GB• Depending on the playback equipment, you may need to set up the equipment. Refer to the operating instructions supplied with each equipment.• B

101GBAdditional Information• When you want to listen to the sound from the TV speaker, set the “HDMI Audio Out” to “TV+AMP” in the HDMI Settings menu

102GB• Audio signals (format, sampling frequency, bit length, etc.) transmitted from an HDMI jack may be suppressed by the connected equipment. Check

103GBAdditional Information• Set “HDMI Audio Out” to “AMP” in the HDMI Settings menu (page 88).• You can enjoy High Bitrate Audio (DTS-HD Master Audio

104GB• Press AMP, then press DISPLAY repeatedly on the remote control so that the frequency appears on the display panel.RDS does not work.*• Make sur

105GBAdditional Information• Connect the supported USB device (page 44).• Press N to start playback.The USB device cannot be connected into the (USB

106GB• Check the settings of the wireless LAN router/access point and do the setup again. For details on the settings of the devices, refer to the ope

107GBAdditional Information• Refer to the operating instructions of your wireless LAN router/access point, and check the multicast setting. If the mul

108GB• Confirm that the network is correctly set up. If it is not, the connection cannot be made (page 90).• The device on the device list is set to “

109GBAdditional Information• The receiver is not selected as the remote speaker on the iOS device. Select the receiver as the network speaker.You cann

11GBN Dolby Pro Logic indicatorLights up the respective indicator when the receiver performs Dolby Pro Logic processing. This matrix surround decoding

110GBIf there is a malfunction, a message appears on the display panel. You can check the condition of the system by the message. If any problem persi

111GBAdditional InformationSpecificationsAmplifier sectionMexico model1)Minimum RMS Output Power(6 ohms, 20 Hz – 20 kHz, THD 0.09%) 90 W + 9

112GBHDMI VideoInput/Output (HDMI Repeater block)iPod/iPhone sectionDC 5V 1.0 A MAXUSB sectionSupported bit rate*MP3 (MPEG 1 Audio Layer-3):32 kbps –

113GBAdditional InformationNETWORK sectionEthernet LAN10BASE-T/100BASE-TXWireless LANCompatible standards: IEEE 802.11 b/gSecurity:WEP 64 bit, WEP 128

114GBIndexNumerics2 channel 505.1 channel 197.1 channel 19AA.F.D. mode 50A/V Sync. 87, 95Access Point Scan 36Advanced Auto Volume 87AirPlay 68Alphabet

115GBAdditional InformationFFast View 89Fixed IP address 37FM 47FM Mode 47, 95HHD-D.C.S. 50HDMI 95HDMI Audio Out 88, 95HDMI Settings 88, 95Home Networ

116GBSoftware Update 91Sound Effects 50Sound field 50Speaker Pattern 84, 93Speaker Settings 82, 93SPEAKERS 34Subwoofer Level 89Super Audio CD player 2

117GBEND-USER LICENSE AGREEMENT FOR SONY SOFTWAREYou should carefully read the following agreement before using the SONY SOFTWARE (defined below). Us

118GBEXCLUSION OF WARRANTY ON SONY SOFTWAREYou expressly acknowledge and agree that use of the SONY SOFTWARE is at your sole risk. The SONY SOFTWARE i

12GBA DIGITAL INPUT/OUTPUT sectionB TUNER sectionC NETWORK sectionD SPEAKERS section (page 21)E AUDIO INPUT/OUTPUT sectionF VIDEO INPUT/OUTPUT section

©2013 Sony Corporation Printed in Malaysia4-454-467-52(1)

13GBUse the supplied remote control to operate this receiver and other equipment. The remote control is assigned to operate Sony audio/video equipment

14GB– select track numbers. Press 0/10 /= to select track number 10.– select channel numbers.– select the letters (ABC, DEF, etc.).– select .@ for pun

15GBO +/–Adjust the volume level of all speakers at the same time.PTurns off the sound temporarily. Press the button again to restore the sound.Q RET

16GBTo control other Sony equipmentName TV VCR DVDplayerBlu-ray Disc playerCD playerB TV ?/1zC Numeric buttonszz z z zCLEARzz zG POP UP/MENUzzTOP MENU

17GBGetting startedYou can enjoy your audio/video equipment connected to the receiver by following the simple steps below.Before connecting cords, be

18GBDigital audio formats that this receiver can decode depend on digital audio output jacks of the equipment connected. This receiver supports the fo

19GBConnections1: Installing the speakersThis receiver allows you to use up to a 7.2 channel system (7 speakers and 2 subwoofers).Example of speaker s

2GBTo reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.To reduce the risk of fire, do not cover the ventila

20GB7.1 channel speaker system using front high speakersYou can enjoy vertical sound effects by connecting additional two front high speakers.Place th

21GBConnections2: Connecting the speakersBefore connecting cords, be sure to disconnect the AC power cord (mains lead).A Monaural audio cord (not supp

22GB* When you connect a subwoofer with an auto standby function, turn off the function when watching movies. If the auto standby function is set to o

23GBConnections3: Connecting the TVYou can watch the selected input image when you connect the HDMI TV OUT or MONITOR OUT jack to a TV. You can operat

24GBTo enjoy the TV broadcast in multi channel surround sound from the receiver* If your TV is compatible with the Audio Return Channel (ARC) function

25GBConnectionsNotes on HDMI connections• Depending on the TV or the video equipment, 4K or 3D images may not be displayed. Check the HDMI video forma

26GBIf your equipment does not have an HDMI jack, see page 27.Connecting equipment with HDMI jacksBlu-ray Disc playerAAudio/video signalsSatellite tun

27GBConnectionsA Optical digital cord (not supplied)B Audio cord (not supplied)C Video cord (not supplied)Connecting equipment with jacks other than H

28GB4b: Connecting the audio equipmentBefore connecting cords, be sure to disconnect the AC power cord (mains lead).A Coaxial digital cord (not suppli

29GBConnections5: Connecting the antennas (aerials)Before connecting the antennas (aerials), be sure to disconnect the AC power cord (mains lead).• To

3GBand human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to conser

30GBLAN cable (CAT5) (For a wired LAN connection only)• We recommend that you use this type of cable for a wired LAN.Some flat-type LAN cables are eas

31GBConnectionsThe following illustration is a configuration example of a home network with the receiver and a server.We recommend that you connect th

32GBConnecting the AC power cord (mains lead)Connect the AC power cord (mains lead) to a wall outlet.Turning on the receiverPress ?/1 (on/standby) to

33GBPreparing the Receiver• Measure the frequency characteristics (Phase).1)2)1)The measurement result is not utilized when “Analog Direct” is selecte

34GBTo set the surround back speakersYou can switch the usage of the speaker(s) connected to the SURROUND BACK/BI-AMP/FRONT HIGH/FRONT B terminals in

35GBPreparing the ReceiverTo cancel Auto CalibrationThe Auto Calibration function will be canceled when you perform the following during the measureme

36GBThere are several connecting methods you can use to set up a wireless network: searching for an access point, using a WPS connecting method (eithe

37GBPreparing the ReceiverWhen using a fixed IP addressSelect “Custom”, then press .The IP Address Setting appears on the TV screen.Press . Press V/v

38GBSetting up a wireless network using the WPS PIN code methodIf the access point supports the WPS PIN (Personal Identification Number) code connecti

39GBPreparing the Receiver1 Switch the input of the TV so that an image of the menu is displayed.2 Press HOME.The home menu is displayed on the TV scr

4GB** Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & o

40GBOverview of the home menusPlaying an input source equipment1 Press HOME.The home menu is displayed on the TV screen.2 Select “Watch” or “Listen,”

41GBBasic Operations5 Press 2 +/– to adjust the volume.You can also use MASTER VOLUME on the receiver.6 Press SOUND FIELD +/– to enjoy the surround so

42GBPlaying an iPod/iPhoneYou can enjoy music contents from the iPod/iPhone by connecting it to the (USB) port on the receiver.For details on connec

43GBBasic OperationsYou can select the iPod/iPhone control mode using the iPhone CTRL on the remote control.You can also control all operations by vie

44GB• Do not remove the iPod/iPhone during operation. To avoid data corruption or damage to the iPod/iPhone, turn the receiver off when connecting or

45GBBasic Operations• The receiver is unable to read data other than that saved in the first partition of a hard disk drive.• Operation of models not

46GBNotes on the USB device• Do not remove the USB device during operation. To avoid data corruption or damage to the USB device, turn the receiver of

47GBTuner OperationsListening to FM/AM radioYou can listen to FM and AM broadcasts through the built-in tuner. Before operation, be sure you have conn

48GBYou can enter the frequency of a station directly by using the numeric buttons.1 Press D.TUNING.2 Hold down SHIFT, then press the numeric buttons

49GBTuner Operations1 Select “FM” or “AM” from the menu, then press .2 Select “Select Preset”, then press .3 Select the preset station you want, then

5GBFLAC DecoderCopyright (C) 2000,2001,2002,2003,2004,2005,2006,2007 Josh CoalsonRedistribution and use in source and binary forms, with or without mo

50GBSelecting the sound field1 Select “Sound Effects” from the home menu, then press .2 Select “Sound Field”, then press .3 Select the sound field yo

51GBEnjoying Sound EffectsYou can select the effect type for HD-D.C.S. as follows.•Dynamic: This setting is suitable for an environment which is rever

52GBx Stadium (STADIUM)Reproduces the feeling of a large open-air stadium.x Sports (SPORTS)Reproduces the feeling of sports broadcasting.x Portable Au

53GBEnjoying Sound Effects– PLIIz Height is available only when the speaker pattern is set to a setting with front high speakers.• The sound fields fo

54GB3 Select “Front”, “Center”, “Surround”, or “Front High”, then press .4 Select “Bass” or “Treble”.5 Adjust the gain, then press .• This function d

55GBUsing Network FeaturesAbout the network functions of the receiver• You can enjoy audio content which has been stored on a DLNA-compliant device (D

56GBThis section explains how to set up manufacturer-installed Windows Media Player 12 for Windows 8. For details on how to operate Windows Media Play

57GBUsing Network Features3 Select [Change advanced sharing settings].4 Select [Choose media streaming options] from Media streaming.5 If [Media strea

58GBThis section explains how to set up manufacturer-installed Windows Media Player 12 for Windows 7.For details on how to operate Windows Media Playe

59GBUsing Network Features9 Select [Allow all].The [Allow All Media Devices] window opens. If all the devices in the local network are set to [Allowed

6GBAbout This Manual ...3Supplied accessories ...8Description and location of parts ...

60GB6 Check [Private] and select [Next].7 Confirm that [Location type] is changed to [Private], and select [Close].8 Confirm that [(Private network)]

61GBUsing Network FeaturesEnjoying audio content stored on the serverYou can play back audio content stored on the server using the receiver in MP3, L

62GB• If you select a folder (such as an artist folder, genre folder, etc.), then press the N button, the receiver plays all items in the selected fol

63GBUsing Network FeaturesTo register the TV SideView Device1Press HOME NETWORK.You can also select “HOME NETWORK” from “Listen” in home menu.2 Press

64GB* Depending on the server or track, pause playback may not work when the Home Network function is selected.Enjoying Sony Entertainment Network (SE

65GBUsing Network Features1 Press SEN.The service provider list appears on the TV screen. If the receiver automatically displays the last selected ser

66GBTo listen to the preset station1Press SEN.The service provider list appears on the TV screen. If the receiver automatically displays the last sele

67GBUsing Network FeaturesYou can enjoy the PARTY STREAMING function with other devices* that have this PARTY STREAMING logo shown below.* Available P

68GBThe receiver can join a PARTY that has been started by another device so that you can enjoy the same audio content being played in a different roo

69GBUsing Network Features1 Tap/click on the icon at bottom right of the iOS device screen or iTunes window.[iOS device][iTunes]2 Select “STR-DN840”

7GBOther OperationsSwitching between digital and analog audio (INPUT MODE) ... 77Using other audio input jacks(Audio Inp

70GBUpdating the softwareBy downloading the latest version of the software, you can take advantage of the newest functions. The receiver accesses the

71GBUsing Network FeaturesTo cancel the procedure or to go back to the previous screenPress RETURN O at any point before the receiver starts the softw

72GBSoftware updateSearching for an item using a keywordWhen a list is displayed on the TV screen (such as artist list, a track list, etc.), you can e

73GB“BRAVIA” Sync FeaturesEnter a keyword that will match the letters or a word at the beginning of the name or title of the item you want to search f

74GBPreparing for the “BRAVIA” SyncThe receiver is compatible with the “Control for HDMI-Easy Setting” function.• If your TV is compatible with the “C

75GB“BRAVIA” Sync Features• When you unplug the HDMI cable or change the connection, perform the steps given in “If your TV is compatible with the “Co

76GB• When “Control for HDMI” is set to “On”, the “HDMI Audio Out” settings in the HDMI Settings menu will set automatically based on the System Audio

77GBOther OperationsRemote Easy ControlYou can use the TV remote control to operate the menu of the receiver.Select the receiver (AV AMP) recognized b

78GB• COAX: Specifies the digital audio signals input to the DIGITAL COAXIAL jack.• Analog: Specifies the analog audio signals input to the AUDIO IN (

79GBOther OperationsUsing a bi-amplifier connection1 Select “Settings” from the home menu, then press .The Settings menu list appears on the TV scree

8GBSupplied accessories• Operating Instructions (this manual)(Australia and Mexico models only)• Quick Setup Guide (1)• Remote control (RM-AAU169) (1)

80GBUsing the Settings menuYou can adjust various settings for speakers, surround effects, etc. using the Settings menu.1 Press HOME.The home menu is

81GBAdjusting SettingsSettings menu listSettings Easy Setup(page 82) Speaker Settings(page 82)HDMI Settings(page 88)Audio Settings(page 86)Input Setti

82GBThe menu parameters displayed on the TV screen vary, depending on the current settings or the status of the selected icon.Easy SetupRe-runs the Ea

83GBAdjusting SettingsSelect “WRN Check” in step 2 in “Auto Calibration” (page 82), then press .If a warning message appears, check the message and u

84GBx Calibration Type Lets you select the calibration type after you have performed the Auto Calibration and saved settings.• Full Flat: Makes the me

85GBAdjusting SettingsWhen one of the sound fields for music is selected, no sound is output from the subwoofer if all the speakers are set to “Large”

86GBx Crossover Freq. (Speaker crossover frequency)Lets you set the bass crossover frequency of speakers that the speaker size has been set to “Small”

87GBAdjusting Settingsx Sound Optimizer Lets you enjoy clear and dynamic sound at low volume levels. For details, see “Using the Sound Optimizer funct

88GB• Off: The dynamic range is not compressed.HDMI Settings menuYou can adjust the required settings for equipment connected to the HDMI jack.x Contr

89GBAdjusting Settingsx Subwoofer LevelLets you set the level of the subwoofer to 0 dB or + 10 dB when PCM signals are input via an HDMI connection. Y

9GBDescription and location of partsA ?/1 (on/standby) (page 32, 48, 54)The indicator above the button lights up as follows:Green: The receiver is tur

90GBx InformationLets you check the network information for the network. 1 Select “Information”, then press .2 Select the setting item you want to ch

91GBAdjusting Settingsx Auto StandbyLets you set the receiver switch to standby mode automatically when you do not operate the receiver or when there

92GBThe following options are available in each menu. For details on navigating through menus, see page 91.Overview of the menusMenu[Display]Parameter

93GBAdjusting SettingsSpeaker settings [<SPEAKER>]Speaker pattern[SP PATTERN]5/2.1 to 2/0 (20 patterns)Center Speaker Lift up [CNT LIFT]1 to 10,

94GBFront right high speaker distanceb)[RH DIST.]RH 1.00 m to RH 10.00 m (RH 3’3” to RH 32’9”) (0.01 m (1 inch) interval)Subwoofer distanceb)[SW DIST.

95GBAdjusting SettingsFront high speakers bass level[FH BASS]FH B. –10 dB to FH B. +10 dB (1.0 dB step)Front high speakers treble level[FH TREBLE]FH T

96GBa)You can select this setting only when you have performed the Auto Calibration and saved the settings.b)Depends on the speaker pattern setting, s

97GBUsing the Remote ControlReassigning the input buttonYou can change the default settings of the input buttons to suit the equipment in your system.

98GBResetting the input buttons1While holding down 2 –, press and hold ?/1, then press TV INPUT.2 Release all buttons.The input buttons are reset to t

99GBAdditional InformationOn placement• Place the receiver in a location with adequate ventilation to prevent heat buildup and prolong the life of the